Configuring/resetting iDRAC: Difference between revisions
No edit summary |
No edit summary |
||
| Line 8: | Line 8: | ||
== Solution == | == Solution == | ||
=== Configuration via | === Configuration via System Setup === | ||
iDRAC configuration is part of Setup. Press <F2> during boot to enter | Connect keyboard, video and mouse to the appliance front or back. | ||
On recent models (12th generation and after), iDRAC configuration is part of System Setup. Press <F2> at server startup to enter setup. | |||
On older models (11th generation and before), you may have to press <Ctrl-E> during the boot process to enter iDRAC configuration. | |||
| | ||
=== Configuration and reset via server's operating system === | === Configuration and reset via server's operating system === | ||
Racadm will try to launch a graphic shell which isn't installed. Omit all warnings in regard to Xlib. | |||
RACadmin is installed on all Fluke Networks, Visual Networks, Netscout and COMCERT DELL bases appliances. To use RACadmin, you must be root user. | RACadmin is installed on all Fluke Networks, Visual Networks, Netscout and COMCERT DELL bases appliances. To use RACadmin, you must be root user. | ||
Login to the CLI and if not already rioot, asume root priviledges: | Login to the CLI and if not already rioot, asume root priviledges: | ||
<pre>$ sudo su -</pre> | <pre>$ sudo su - | ||
</pre> | |||
To reset the iDRAC interface: | |||
This is just a reset; it does not clear the current configuration. | |||
<pre># racadm racreset</pre> | |||
To view the iDRAC IP configuration: | |||
<pre># racadm getniccfg</pre> | |||
To | To set a static IP address: | ||
The format is <address> <mask> <default route> | |||
<pre># racadm</pre> | <pre># racadm setniccfg -s 192.168.0.120 255.255.255.0 192.168.0.1</pre> | ||
To | To enable DHCP: | ||
<pre># racadm </pre> | <pre># racadm setniccfg -d</pre> | ||
Revision as of 18:01, 3 March 2018
Introduction
All Fluke Networks, Visual Networks, Netscout and COMCERT DELL bases appliances come with a iDRAC Management Interface with dedicated NIC. Its is highly recommended to configure this interface appropriately to allow remote access to the appliance and to send system alerts to a network manegement station of your choice.
Solution
Configuration via System Setup
Connect keyboard, video and mouse to the appliance front or back.
On recent models (12th generation and after), iDRAC configuration is part of System Setup. Press <F2> at server startup to enter setup.
On older models (11th generation and before), you may have to press <Ctrl-E> during the boot process to enter iDRAC configuration.
Configuration and reset via server's operating system
Racadm will try to launch a graphic shell which isn't installed. Omit all warnings in regard to Xlib.
RACadmin is installed on all Fluke Networks, Visual Networks, Netscout and COMCERT DELL bases appliances. To use RACadmin, you must be root user.
Login to the CLI and if not already rioot, asume root priviledges:
$ sudo su -
To reset the iDRAC interface:
This is just a reset; it does not clear the current configuration.
# racadm racreset
To view the iDRAC IP configuration:
# racadm getniccfg
To set a static IP address:
The format is <address> <mask> <default route>
# racadm setniccfg -s 192.168.0.120 255.255.255.0 192.168.0.1
To enable DHCP:
# racadm setniccfg -d